9 Best Fish Finder Mounts for Bass Boats (November 2026)
The best bass boat fish finder mounts include the WINDFRD Aluminum Swing Arm Fish Finder Mount for large screens, the VAUBORTTI Aluminum Fish Finder Mount for T-bolt tracks, and the Vadaxx Fish Finder Mount Base for simple surface mounting.
On this page (4 sections)
The WINDFRD Aluminum Swing Arm Fish Finder Mount is the best bass boat fish finder mount for most anglers. It fits 5–12 in screens, uses powder-coated marine-grade aluminum and stainless steel hardware, and rotates 360 degrees from two pivot points.
A console screen and a casting deck screen do different work. The console display must stay readable while you steer, and the bow display must stay readable while you stand and cast.
Choose VAUBORTTI if your boat uses a T-bolt track. Pick Bzcovac or Velpaw for a taller casting deck display, and choose PROcise Outdoors for a fixed console layout.
A good mount does more than hold a screen. It should keep the display readable while you steer, cast or move around the boat.
The best choice depends on screen size, mounting surface, arm reach and how often you change the angle. A short base suits a flat console where you mostly sit in one position, while a taller riser suits a deck where you alternate between sitting and standing.
Set the screen at your eye level. Too low forces you to look down, and too high can create glare or move the display out of your normal line of sight.
Check what surrounds the mount. Steering controls, throttle levers, rod holders, seats and windshields can limit how far a screen can swing, so wide rotation only helps if the deck gives it room.
Plan cable routing before drilling the base in place. A tight cable can pull on the display when the mount turns.
If you are still deciding on the general layout, start with best fish finder mount for boat. For the location itself, see where to mount a fish finder on a boat.
Salt water, fresh water and sun affect a mount over time. Powder-coated aluminum and stainless steel hardware help, but regular rinsing and fastener checks still matter.
Our picks at a glance
-
1
Best for large screensWINDFRD Aluminum Swing Arm Fish Finder Mount
9.6/10 our score
See it on Amazon -
2
-
3
- 4
Check itBzcovac Marine Electronic Mount
Best for adjustable standing height - 5
Check itEDSRDPLT Fish Finder Mount Base
Best for lighter screens - 6
Check itWINDFRD Aluminum Fish Finder Mount for Boat
Best for a tall bow setup - 7
Check itVAZESWIN 1.5 Ball Aluminum Alloy Fish Finder
Best for a medium-length arm - 8
Check itVelpaw 20.7” Telescoping Fish Finder Mount
Best for deck height changes - 9
Check itPROcise Outdoors Angled Fish Finder and GPS Puck
Best for an integrated console
The best bass boat fish finder mounts for consoles and decks
These bass boat fish finder mounts cover fixed deck brackets, rotating bases, rail-track systems and tall bow setups. The top picks have the widest mix of screen support, adjustment and marine-ready materials.
Our score weighs specs, features and buyer feedback against what you are shopping for. We checked the mounting style, stated screen guidance, adjustment range, materials, included hardware and the practical needs of bass boat consoles and casting decks.
| Product | Best for | Screen range | Material | Mounting | Our score |
|---|---|---|---|---|---|
| WINDFRD Aluminum Swing Arm Fish Finder Mount | large screens | 5–12 in | Powder-coated marine-grade aluminum and stainless steel | Drill-down flat surface mount | 9.6 |
| VAUBORTTI Aluminum Fish Finder Mount | T-bolt tracks | Marine-grade aluminum alloy with TPU ball | Rail track mount | 9.4 | |
| Vadaxx Fish Finder Mount Base | simple surface mounting | Surface mount | 9.2 | ||
| Bzcovac Marine Electronic Mount | adjustable standing height | Anodized aluminum and stainless steel | Flat surface mount | 9.1 | |
| EDSRDPLT Fish Finder Mount Base | lighter screens | Marine-grade composite and stainless steel bolts | Surface mount | 9.0 | |
| WINDFRD Aluminum Fish Finder Mount for Boat | a tall bow setup | 8.9 | |||
| VAZESWIN 1.5 Ball Aluminum Alloy Fish Finder | a medium-length arm | 6061-T6 aluminum alloy | Drill-down mount | 8.6 | |
| Velpaw 20.7” Telescoping Fish Finder Mount | deck height changes | Anodized aluminum | 8.2 | ||
| PROcise Outdoors Angled Fish Finder and GPS Puck | an integrated console | Marine-grade aluminum | Deck mount | 8.1 |
WINDFRD Aluminum Swing Arm Fish Finder Mount: Best for large screens
- Fits 5–12 in screens
- 110 lb static capacity
- 6 in arm
- 360-degree rotation
A heavy-duty aluminum mount for bass boat consoles or decks, with two pivot points for 360-degree positioning.
Pros
- Supports larger screens
- Salt-spray tested
- Multiple pre-drilled hole patterns
Cons
- Heavier than simple composite bases
- Requires a flat mounting surface
WINDFRD is the strongest all-around choice for a bass boat console or flat deck. The 5–12 in screen range covers many common fish finder sizes, including larger displays that need more support than a small plastic base can offer.
Its all-aluminum construction has a stated 110 lb static capacity and 22 lb dynamic capacity. The 6 in arm uses two pivot points, so you can rotate the screen through 360 degrees and set the display toward the driver or the person fishing from another seat.
The rectangular base has several pre-drilled hole combinations. It can mount on a boat dashboard or deck, and the package includes 4 sets of 316 marine-grade stainless steel machine screws, lock nuts and sheet metal screws.
This mount makes the most sense when your bass boat has a flat surface and you want one strong bracket for a console screen. It is also a good fit for anglers who need more viewing flexibility than a fixed deck plate provides.
VAUBORTTI Aluminum Fish Finder Mount: Best for T-bolt tracks
- 1.5 in C-size ball
- One-piece aluminum construction
- Oversized adjustment knob
- AMPS hole pattern
A track-based mount for anglers who want quick repositioning and compatibility with common 1.5 in arm systems.
Pros
- Easy-to-grip knob
- Fits 1.5 in arms and adapters
- One-piece die-cast aluminum
Cons
- Confirm the track and device hole pattern
- Specific Humminbird models may not fit
VAUBORTTI suits a bass boat with a compatible rail track and an angler who changes the screen position often. Its 1.5 in C-size TPU ball works with 1.5 in, 38 mm and C-size arms and adapters from RAM Mounts, Arkon, iBolt and other compatible systems.
The one-piece marine-grade aluminum body uses a powder-coated finish. An oversized wing-style knob gives you more grip when you adjust the angle with wet hands or gloves.
Its rectangular plate includes an AMPS hole pattern and other pre-drilled patterns for fish finders, GPS units and marine electronics. VAUBORTTI lists compatibility with many Garmin and Lowrance units, but specific Humminbird and Solix models need careful checking.
Choose this mount when track mounting and modular arm compatibility matter more than a built-in tall riser. It is a flexible choice for a console or deck where you want to loosen, reposition and tighten the display without changing the base.
Vadaxx Fish Finder Mount Base: Best for simple surface mounting
- Dual 360-degree swivel
- Nylon and stainless steel
- 6.3 in upper mount
- Includes 4 screws and 4 nuts
A compact surface-mount base with broad adjustment and a flat plate that can be drilled for a matching device pattern.
Pros
- Dual swivel adjustment
- Hardware included
- Works with several Garmin and Lowrance models
Cons
- Not water resistant
- The fish finder is not included
Vadaxx is a practical choice for a surface-mounted bass boat display that needs wide angle adjustment. The dual 360-degree swivel design lets you rotate both the mount and the bracket, while the upper mount measures 6.3 in wide.
The base is 2.6 in across, and the swivel ball is 1.8 in in diameter. The nylon and stainless steel construction keeps the design light, but its stated water resistance level is not water resistant, so place it where direct spray is limited and care for the hardware regularly.
The flat plate has several mounting holes, and you can drill your own holes to match a device. The package includes 4 screws and 4 nuts, which helps with a basic installation.
This is a good fit for anglers who want a simple rotating base without a long arm or tall column. For a boat that stays in heavy spray, compare its material and water-resistance details with the aluminum options above.
Bzcovac Marine Electronic Mount: Best for adjustable standing height
- 18–24 in telescoping height
- 350-degree monitor swivel
- 180-degree base swivel
- Anodized aluminum
A tall mount for a console, deck or electronic box where seated and standing anglers need different viewing heights.
Pros
- Wide height range
- Pre-drilled mounting plate
- Fits major marine electronics brands
Cons
- Heavier 5 lb design
- Takes more room than a low base
Bzcovac is the best choice here when your bass boat needs an adjustable standing-height screen. Its telescoping riser moves from 18 to 24 in, which can help keep a fish finder visible from a console seat or a casting deck position.
That height range suits anglers who do not fish from one fixed posture. You can set the screen lower for a seated view at the console.
You can raise it for a standing view on the casting deck without bending to read the display.
The monitor plate swivels 350 degrees. The base swivels 180 degrees, and the riser tilts 180 degrees, giving you several ways to point the display without moving the whole mount.
Those separate movements help when the best viewing angle changes through the day. You might face the screen toward the driver in the morning.
You might turn it toward the bow later when you are casting from a different spot.
The bracket uses anodized aluminum and stainless steel hardware. It includes the mounting bracket, plate, telescoping riser and a hardware set with screws, nuts and washers.
The pre-drilled plate fits major brands including Garmin, Humminbird, Lowrance, Simrad and Raymarine. That broad fit helps if you switch brands or move the display from another setup.
This mount needs more room than a low surface base, and its 5 lb weight matters during installation. Check that the riser can extend and swivel without hitting a seat, windshield or storage lid.
Pick it when height and broad viewing angles solve a real problem on your boat. For a flat console where you sit in one place, a lower base may be simpler.
EDSRDPLT Fish Finder Mount Base: Best for lighter screens
- Dual ball joints
- 1.5 in ball
- Marine-grade composite construction
- AMPS pattern
A lightweight rotating base for smaller bass boat displays, with clear limits for screens from 9 to 12 in and larger units.
Pros
- Lightweight composite body
- 360-degree adjustment
- Disassembles for installation
Cons
- Not suitable for screens over 12 in
- Not compatible with listed Humminbird Helix and Solix models
EDSRDPLT fits anglers who want a light rotating base for a smaller bass boat display. Its dual ball-joint system provides 360-degree adjustment, and the 1.5 in ball is intended to give stronger clamping force than a smaller ball.
That design suits a console or deck where you turn the screen toward different seats. You can loosen the switch, set the angle, then tighten it again for a secure hold.
The marine-grade composite body uses stainless steel bolts and is designed to resist wear, corrosion and UV damage. The brand recommends screens 9 in or less, advises extra attention to screw tightness for 9–12 in units, and says screens over 12 in are not suitable.
Those limits are central to choosing this mount. A smaller display places less leverage on the ball joints.
A larger display needs closer attention during installation and regular checks after use.
Compatibility includes selected Garmin, Lowrance and Raymarine units. It is not compatible with the Humminbird Helix 5, 7, 8, 10, 12 or 15, or Solix 10, so check your exact fish finder before drilling.
The base and bracket can be disassembled separately for installation. That helps on a boat or kayak where you want to fix the base first and add the bracket after the display is attached.
Choose EDSRDPLT when low weight and quick removal matter. Its limits make it a better fit for a smaller console or deck screen than a large tournament-style display.
WINDFRD Aluminum Fish Finder Mount for Boat: Best for a tall bow setup
- 18.3 in double socket arm
- 6.23 x 2 in mounting plate
- 2.4 in AMPS base
- Two ball-joint adjustments
A tall bow electronics bracket that raises a smaller screen for sitting or standing, with a 5 lb static limit.
Pros
- Long reach
- Powder-coated aluminum
- 316 marine-grade mounting hardware included
Cons
- Best with screens up to 7 in
- Long arm can sag with heavier displays
The tall WINDFRD bow mount helps raise a smaller fish finder above a bass boat casting deck. Its 18.3 in C-size double socket arm gives you more reach than a short base, and the two ball joints allow many viewing angles.
That reach can keep the screen clear of deck clutter and closer to a standing angler. It also lets you move the display forward without moving the base.
The package includes the extra-long arm, a 6.23 x 2 in device plate and a 2.4 in AMPS-pattern round base. It also includes 316 marine-grade stainless steel machine screws, lock nuts and sheet metal screws.
The AMPS pattern helps with direct installation on a boat, kayak or flat surface. The plate also has other pre-drilled combinations for marine GPS, CB radios, ham radios and gimbal brackets.
The key limit is the 5 lb static capacity. WINDFRD recommends using it with screens up to 7 in because larger or heavier units may sag, shift or become harder to adjust on the long arm.
That limit reflects the leverage of a long arm. The farther the screen sits from the base, the more movement it can create at the joints when the boat rocks.
Pick this mount when a standing bow view matters and your screen stays within the stated limit. For a larger display, the shorter heavy-duty WINDFRD swing arm is the safer match.
VAZESWIN 1.5 Ball Aluminum Alloy Fish Finder: Best for a medium-length arm
- 9.1 in double socket arm
- 2.4 in round base
- 6.25 x 2 in plate
- 1.5 in TPU balls
A 9.1 in aluminum arm for bass boats, kayaks and pontoons that need more reach than a short base without a tall riser.
Pros
- C-size component system
- 360-degree adjustment
- Fits many Garmin and Lowrance units
Cons
- Installation screws are not included
- Specific Humminbird models are excluded
VAZESWIN sits between a short surface base and a tall bow column. Its 9.1 in double socket arm gives extra reach, while the 2.4 in round base and 6.25 x 2 in rectangular plate create a complete C-size mounting setup.
That middle length suits anglers who need more reach than a compact base but do not need a tall riser. The screen can sit clear of a console edge while staying lower than a bow column.
The base and plate use thickened 6061-T6 aluminum alloy with a hard-anodized surface. The arm uses powder-coated 6061-T6 aluminum, and the 1.5 in TPU balls give 360-degree adjustment through the ball-and-socket design.
The round base includes pre-drilled holes, including the universal AMPS hole pattern. That pattern allows direct installation on a boat, kayak or any flat surface.
This mount fits many Garmin and Lowrance models, plus compatible RAM Mounts, Arkon and iBolt components. It has partial compatibility with Humminbird and Raymarine, and the listed Humminbird Helix and Solix models are excluded.
The package includes the arm, rectangular plate and round base, but installation screws and other hardware are not included. Choose it when you already have suitable mounting hardware and want a medium-length aluminum arm.
Plan the hardware before you start drilling. The right screws and nuts matter as much as the holes in the base, especially on a vibrating deck.
Velpaw 20.7” Telescoping Fish Finder Mount: Best for deck height changes
- 14.68–20.7 in height adjustment
- Dual 360-degree swivel
- 100 lb static capacity
- Deck screws included
A bow-deck mount with tool-free height adjustment for anglers who alternate between seated and standing positions.
Pros
- Large height range
- Mounting screws included
- Designed for flat boat decks
Cons
- 6.4 lb weight
- Not intended for kayak installation
Velpaw is built for a bass boat bow deck where anglers switch between sitting and standing. Its telescoping column adjusts from 14.68 to 20.7 in without tools, and dual 360-degree swivel joints let you reposition the display.
Tool-free height adjustment helps when the fishing position changes during a trip. You can raise the screen for a standing cast and lower it when you sit to move the boat.
The 3.54 in square base has 4 mounting slots and included screws for flat deck installation. The package also includes the telescoping column, rotating arm, multi-hole plate and deck base.
The multi-hole plate has a 6.23 in pattern that accommodates various mounting patterns. It is compatible with select Garmin ECHOMAP, GPSMAP and STRIKER Plus, Lowrance HDS LIVE and HOOK Reveal, and Humminbird HELIX 8 and 9 displays.
Velpaw states a 100 lb static and 22 lb dynamic load capacity and uses anodized aluminum. The mount weighs 6.4 lb, so plan the installation before placing it on a narrow or crowded casting deck.
The weight and height mean this mount needs a firm, flat deck area. Check that the column can extend without blocking a hatch, seat or foot control.
It is made for boat decks rather than kayak installation. Pick it when a tall, height-adjustable screen is more useful than a compact base, especially if you fish from both seated and standing positions.
PROcise Outdoors Angled Fish Finder and GPS Puck: Best for an integrated console
- 22.5-degree angle
- Fish finder and GPS puck layout
- 15.5 x 5.5 x 4.5 in size
- Pre-drilled holes
A fixed angled deck bracket for a clean bass boat console or deck layout with space for both a fish finder and GPS puck.
Pros
- Organized dual-device layout
- Powder-coated finish
- Fits Garmin, Lowrance and Humminbird
Cons
- Fixed 22.5-degree angle
- Needs deck space for its 15.5 in length
PROcise Outdoors is the cleanest choice for a fixed bass boat console or deck layout that combines a fish finder with a GPS puck. Its 22.5-degree angle points the electronics toward the angler instead of leaving the display flat.
That fixed angle can reduce glare and make the screen easier to read from a seated position. It also gives the setup a more organized look than a loose bracket on the console.
The bracket measures 15.5 x 5.5 x 4.5 in and is made from marine-grade aluminum with a black powder-coated finish. Pre-drilled holes support a more direct installation and can help keep the electronics layout organized.
The finish resists corrosion, scratches and UV damage in the product description. That matters for a deck mount that faces sun and spray through a full season.
It fits Garmin, Lowrance and Humminbird fish finders and marine electronics. The deck-mount design is intended for a bass boat console, trolling motor deck or similar professional rigging setup.
Choose PROcise when you want an integrated, low-profile arrangement and do not need a rotating ball mount. Its fixed angle and 15.5 in length require more planning than the adjustable bases.
Measure the deck space before you commit to this layout. A long bracket needs clear room, and the 22.5-degree angle needs room to face the angler without crowding controls.
How do you choose fish finder mounts for bass boats?
The best fish finder mounts for bass boats match the screen, mounting surface and viewing position. Start with display size, then choose a fixed bracket, rotating ball mount, rail-track base or tall deck riser.
Screen size sets weight and leverage. A compact display can work on a light base, while a larger display needs stronger material, a firmer base and room to swing without hitting nearby gear.
For console use, a flat surface mount keeps the display near the steering area. The WINDFRD swing arm gives broad adjustment, while PROcise Outdoors gives a fixed 22.5-degree layout for a fish finder and GPS puck.
Keep the console screen clear of steering controls, throttle levers and seats. Leave a clean path for power and transducer cables.
A fixed bracket looks tidy, while a rotating arm helps when passengers change seats.
For a casting deck, height and reach matter more. Bzcovac adjusts from 18 to 24 in, Velpaw adjusts from 14.68 to 20.7 in, and the tall WINDFRD arm reaches 18.3 in.
Check that a tall riser can extend and turn without striking a seat, windshield, rod holder or storage lid.
The long-arm WINDFRD is limited to 5 lb static capacity and is recommended for screens up to 7 in. Arm length and screen weight must be read together, since a heavy display can sag or shift on the joints.
Aluminum mounts with stainless steel hardware suit harsh marine use, while composite bases can be lighter but need checking for stated limits and water resistance before use in heavy spray. You can also compare our guide to best fish finder bow mounts if the display will sit near the trolling motor.
A drill-down base needs a flat surface and solid backing, a track base needs a compatible rail, and a fixed deck bracket needs enough length.
What should you check before installing a bass boat fish finder mount?
Check the flat surface, hole pattern, screen weight, cable reach and the angle you need before drilling. A mount can fit a device pattern but still be a poor fit if the arm blocks controls or the base crowds the deck.
Start by marking the spot on the console or deck. Hold the screen at the height and angle you will use while fishing.
Then check whether the base, arm and cables clear seats, levers, lids and other electronics through the full range of movement. Measure the available deck or console area first.
Long brackets such as the PROcise Outdoors mount need more length, while tall risers need room to rotate without hitting a seat, windshield or other electronics. Tall mounts also need vertical clearance.
A telescoping riser that extends to 20.7 in or 24 in can change how a screen sits under a windshield or bimini top. Test the extended position before marking the final holes.
Check whether the mount includes hardware. Vadaxx includes 4 screws and 4 nuts, Velpaw includes base installation screws, and VAZESWIN does not include installation screws or other hardware.
Included hardware does not remove the need to check fit. Make sure the screws suit the deck material and that the base sits flat.
A base that rocks on a curved or uneven surface will move under load. Clean and dry the hardware after use, especially in salt water.
Keep knobs tight without over-tightening them, and inspect the base and bolts for movement. UV exposure can also affect plastic and composite parts over time.
Store the mount out of direct sun when you can, and rinse salt from joints and knobs after trips. Our guide to the best fish finders for bass compares the display and sonar side of the setup.
Finally, check the cable path after the mount is fixed. A cable should have enough slack to allow rotation without pulling the display, and stay clear of hinges and walkways.
Which bass boat fish finder mount should you choose?
Choose the WINDFRD Aluminum Swing Arm Fish Finder Mount if you want the broadest screen range and a strong rotating aluminum base. Choose VAUBORTTI for a compatible T-bolt track, Vadaxx for a simple adjustable surface base, and Bzcovac or Velpaw for a taller deck view.
For a smaller screen, EDSRDPLT keeps the design light, while the tall WINDFRD bow mount adds reach with a clear 5 lb limit. VAZESWIN suits a medium-length arm, and PROcise Outdoors is the better choice for a fixed 22.5-degree fish finder and GPS puck arrangement.
Match the pick to the boat layout first. A flat console favors a compact base or a fixed angled bracket, while a casting deck favors a riser or long arm that lifts the screen to a standing view.
Match the pick to the screen second. Larger displays need a mount with stated capacity that leaves room for boat movement, while smaller displays give you more options, including lighter composite bases and taller arms within their stated limits.
Match the pick to the surface third. A drill-down base needs a flat area, a track base needs the right rail, and a fixed deck bracket needs length and a clear viewing angle.
If your boat is a pontoon or jon boat rather than a bass boat, compare the best fish finder mount for pontoon boat and best fish finder mount for jon boat. For basic sonar expectations, read [Do Fish Finders Really Work?
What to Know](/do-fish-finders-really-work/).
A castable setup may need a different approach, explained in How Does a Castable Fish Finder Work? What to Know.
For most bass boat anglers, the WINDFRD swing arm remains the safest starting point.
It covers 5–12 in screens, rotates through 360 degrees and uses marine-grade aluminum with stainless steel hardware. If you fish standing at the bow, look closer at the tall options.
Bzcovac and Velpaw give height adjustment, while the tall WINDFRD arm gives fixed long reach for a smaller screen. Weigh the tradeoffs before you drill.
A strong console mount may add weight, a tall deck mount may need more clearance, and a light base may suit only smaller displays. The right mount fits your layout, your screen and your surface without forcing compromises on readability.
Our top 3 picks at a glance
-
1
Best for large screens
WINDFRD Aluminum Swing Arm Fish Finder Mount
9.6/10 our score
See it on Amazon -
2
-
3
Frequently asked questions
Where should you mount a fish finder on a bass boat?
Mount a console display where you can read it while driving, and place a second screen on the casting deck if you fish from the bow. Keep the screen clear of steering controls, protect the cable path, and choose a base that matches the deck or console surface.
What size fish finder mount do bass boats need?
Match the mount to the screen size, arm length and weight. The WINDFRD swing arm fits 5–12 in screens, while the long WINDFRD bow arm is recommended for screens up to 7 in because its static capacity is 5 lb.
Check the mount limits before choosing a large display.
Are ball mounts good for bass boat fish finders?
Ball mounts are useful when you need to change the viewing angle between seated and standing positions. A 1.5 in or 1.8 in ball can provide broad adjustment, but a long arm creates more leverage, so larger screens need a mount with a suitable capacity and a firm base.
Can one fish finder mount work on the console and bow?
Sometimes, but the best choice depends on the surface and viewing height. A flat surface base may suit the console, while a tall deck mount works better on a casting deck.
Moving one mount between locations also means checking cable reach, hole placement and screen angle each time.
