Best picks

9 Best Fish Finder Mounts for Inflatable Boats (November 2026)

Updated on · By the Fish Finder Critic team

The best fish finder mounts for inflatable boats include the WINDFRD Aluminum Swing Arm Fish Finder Mount for large screens on a rigid mount point, the Vadaxx Fish Finder Mount Base for a simple ball-mount base, and the EDSRDPLT Universal Kayak Fish Finder Mount for tool-free track mounting.

On this page (9 sections)
  1. The best fish finder mounts for inflatable boats, ranked
  2. How do these mounts compare for inflatable tubes?
  3. How we compared these mounts
  4. Which base is safest for inflatable tubes?
  5. What screen size should you mount on an inflatable?
  6. Do you need a track mount or a swing arm?
  7. How do you keep a mount steady on a flexing hull?
  8. What should you check before you order?
  9. Verdict: which mount should you buy for an inflatable boat?

The best fish finder mount for inflatable boat use is the WINDFRD Aluminum Swing Arm Fish Finder Mount, thanks to its all-aluminum build and fit for 5 to 12 inch screens. The best fish finder mount for inflatable boat setups without drilling into tubes is a clamp or track option, like the Deeper flexible arm or a track kit.

Our score weighs specs, features and buyer feedback against what you are shopping for.

Inflatable boats flex in ways rigid hulls do not. That flex is why the base matters more than style here.

A mount that is steady on a hard deck can wobble if it is fixed to a soft tube. It can also pull at the tube each time the boat rides a wave.

Start with your mount point, not your screen. Find a rigid floor board, transom area or track you can trust.

Then match the arm to the screen size and the angle you need while standing or sitting to fish.

If you are still deciding on placement, read where to mount fish finder on boat first. That guide covers sight lines and reach.

This guide covers bases that protect an inflatable setup.

Our picks at a glance

  1. 1 WINDFRD Aluminum Swing Arm Fish Finder Mount
    Best for large screens on a rigid mount point

    WINDFRD Aluminum Swing Arm Fish Finder Mount

    9.6/10 our score

    See it on Amazon
  2. 2 Vadaxx Fish Finder Mount Base
    Best for a simple ball-mount base

    Vadaxx Fish Finder Mount Base

    9.2/10 our score

    See it on Amazon
  3. 3 EDSRDPLT Universal Kayak Fish Finder Mount
    Best for tool-free track mounting

    EDSRDPLT Universal Kayak Fish Finder Mount

    9.2/10 our score

    See it on Amazon
  1. 4Deeper Kayak Flexible Arm Fish Finder Mount

    Deeper Kayak Flexible Arm Fish Finder Mount

    Best for clamping without drilling
    Check it
  2. 5WINDFRD Fish Finder Track Mount with Transducer

    WINDFRD Fish Finder Track Mount with Transducer

    Best for screen plus transducer on one track
    Check it
  3. 6Leenconghui for Garmin Striker 4 / Plus

    Leenconghui for Garmin Striker 4 / Plus

    Best for small Garmin Striker screens
    Check it
  4. 7xik 1.5 Ball Medium Arm Fish Finder

    xik 1.5 Ball Medium Arm Fish Finder

    Best for Garmin and Lowrance 1.5-inch systems
    Check it
  5. 8Millennium Marine Double Face Marine Electronic MountCheck it
  6. 9BLKGJTF 0368 Fish Finder Mount

    BLKGJTF 0368 Fish Finder Mount

    Best for a compact budget bracket
    Check it

The best fish finder mounts for inflatable boats, ranked

The WINDFRD swing arm leads for large screens on a rigid point. Clamp and track picks follow for tube-safe setups.

Choose by base type before you compare arm length or swing.

1

WINDFRD Aluminum Swing Arm Fish Finder Mount: Best for large screens on a rigid mount point

WINDFRD Aluminum Swing Arm Fish Finder Mount, fish finder mounts for inflatable boats
9.6/10Our score
  • 6-inch arm
  • All-aluminum build
  • For 5 to 12 inch screens
  • 360-degree rotation at two pivot points

A heavy-duty swing arm for 5 to 12 inch screens, made for a flat dashboard, deck or similar rigid surface.

See it on Amazon

Pros

  • All-aluminum construction
  • Two pivot points for rotation
  • Broad Garmin, Lowrance and Humminbird fit

Cons

  • Needs a flat rigid surface for its base
  • Not a no-drill clamp for soft tubes

The WINDFRD Aluminum Swing Arm Fish Finder Mount suits inflatables with a rigid floor board, transom plate or console-like flat surface. It is built for 5 to 12 inch screens with a 6-inch arm.

Its all-aluminum build and stainless steel hardware mean it does not rely on plastic joints for its main strength. The mount is salt spray tested for thousands of hours, which matters for splash and spray on an open inflatable, and it carries a 110 pound static rating with 22 pounds dynamic.

Two pivot points give 360-degree rotation, so you can turn the screen toward you while fishing from either side. That rotation also helps fight glare when the sun moves across a flat, open deck.

WINDFRD lists Garmin, Lowrance and Humminbird models across ECHOMAP, Striker, HDS, Hook, Helix and Solix lines. That wide list matters if you already own a larger unit, and the plate also fits GPS, CB and ham radios for a shared console point.

The trade-off is the base. The rectangle plate needs a flat rigid surface and screws, with supplied 316 stainless screws.

It is not a clamp for a soft tube, and it should not be fixed through an air chamber.

On a small inflatable, that rigidity is a plus when you have a hard point. It is a minus when your boat is a floor-only model with no solid spot to bolt to, where a track or clamp would be safer.

WINDFRD Aluminum Swing Arm Fish Finder MountCheck it on Amazon
2

Vadaxx Fish Finder Mount Base: Best for a simple ball-mount base

Vadaxx Fish Finder Mount Base, fish finder mounts for inflatable boats
9.2/10Our score
  • Dual 360-degree swivel ball mount
  • 6.3-inch wide upper mount
  • 5.9-inch tall bracket with base
  • Nylon and stainless steel

A compact ball-mount base with a flat bracket, suited to a small flat mounting surface.

See it on Amazon

Pros

  • Dual 360-degree swivel
  • Base and bracket separate for install
  • Includes 4 screws and 4 nuts

Cons

  • Requires screws into a flat surface
  • Smaller flat panel than larger arm mounts

The Vadaxx Fish Finder Mount Base suits a small rigid patch on an inflatable, such as a floor board or a plywood transom insert. It gives you a dual 360-degree swivel ball mount on a compact base.

The upper mount is 6.3 inches wide and the bracket with base stands 5.9 inches tall. That low height can help on a low inflatable where a tall pedestal would block your view or raise the center of gravity.

The 2.6-inch base diameter and 1.8-inch swivel ball give a stronger clamp than a small ball alone. The base and bracket separate, so you can fix the base first and add the screen after, which is handy if you need to seal screw holes or reach a tight spot.

Vadaxx lists many Garmin GPSMAP, ECHOMAP and Striker models, plus Lowrance HDS Carbon and HDS LIVE units. The package has 4 screws and 4 nuts, and the flat panel lets you drill your own holes if your model is not in the pre-drilled pattern.

The trade-off is that it still needs screws into a flat surface, and it is listed as not water resistant. It is not a tube clamp.

For an inflatable, use it only where the material under the screws is rigid and sealed from air tubes.

Vadaxx Fish Finder Mount BaseCheck it on Amazon
3

EDSRDPLT Universal Kayak Fish Finder Mount: Best for tool-free track mounting

EDSRDPLT Universal Kayak Fish Finder Mount, fish finder mounts for inflatable boats
9.2/10Our score
  • Adjustable 9 to 14 inch arm
  • Tool-free rail install
  • 1.5-inch ball head and track base
  • Includes telescoping transducer arm

A tool-free track kit with a 9 to 14 inch adjustable arm for screen and transducer sizing.

See it on Amazon

Pros

  • No tools or drilling for track install
  • Adjustable arm length
  • Includes transducer arm

Cons

  • Needs a compatible gear track
  • Less rigid than an all-aluminum swing arm

The EDSRDPLT Universal Kayak Fish Finder Mount suits inflatables that already have a gear track on a rigid rail or floor board. It installs with no tools and no drilling on that track.

The adjustable arm runs 9 to 14 inches. That range helps you move the screen away from your knees or rods without buying a second arm, and it gives you room to fine tune transducer angle and depth for clearer readings.

The kit has a 1.5-inch ball head, a fish finder mount, a track base and a telescoping transducer arm. One base can therefore handle screen position and transducer angle, which keeps a small inflatable deck less crowded than two separate mounts.

EDSRDPLT says it fits most Garmin, Lowrance and Humminbird models. The build uses marine-grade composite and stainless steel for sun, salt and splash use, with a water resistant rating in the specs.

The trade-off is track dependence. If your inflatable has no track, this kit does not create a mount point by itself.

A rigid arm bolted to a floor board will feel steadier in chop, so check your boat before you choose this route.

EDSRDPLT Universal Kayak Fish Finder MountCheck it on Amazon
4

Deeper Kayak Flexible Arm Fish Finder Mount: Best for clamping without drilling

Deeper Kayak Flexible Arm Fish Finder Mount, fish finder mounts for inflatable boats
9.1/10Our score
  • 31-inch flexible arm
  • G-Clamp for objects 2.7 inches thick or less
  • Adjusts by up to 8 inches while mounted
  • For Deeper Chirp and PRO series

A long flexible arm with a G-Clamp, built to hold a Deeper sonar at the surface.

See it on Amazon

Pros

  • No drilling required
  • Long 31-inch arm for positioning
  • Clamp fits up to 2.7 inches

Cons

  • Made for Deeper models, not standard screens
  • Flexible arm moves more than a rigid arm

The Deeper Kayak Flexible Arm Fish Finder Mount 2.0 suits inflatable boats when you fish with a Deeper sonar. Its G-Clamp fits objects 2.7 inches thick or less, so it can grip a transom board or thick floor edge without screws.

The arm is 31 inches long. That length lets you place the sonar at the surface while you stay seated away from it.

Deeper says the arm adjusts by up to 8 inches while mounted, so you can raise or lower it without removing the clamp.

The flexible column makes height changes quick when you move between boats. It also uses a wave rider design to help the sonar stay at the surface for phone connection, which is the point of this mount rather than holding a fixed screen.

Materials mix stainless steel, aluminum and fiber-glass reinforced plastic. That mix keeps the long arm light at 0.21 kg while still clamping hard enough for higher trolling speeds.

Trade-off: this is not a mount for a standard fish finder screen. It is made for Deeper Chirp and PRO series models.

If you run a Garmin or Lowrance display, a ball or swing arm will fit better.

For a standard screen, our castable fish finder guide explains how Deeper-style units differ.

Deeper Kayak Flexible Arm Fish Finder MountCheck it on Amazon
5

WINDFRD Fish Finder Track Mount with Transducer: Best for screen plus transducer on one track

WINDFRD Fish Finder Track Mount with Transducer, fish finder mounts for inflatable boats
8.8/10Our score
  • 1.5-inch double-socket ball
  • Transducer arm extends 11.42 to 17.91 inches
  • Universal track ball with T-bolt
  • Drill-down mounting track included

A 2-in-1 track mount that holds a display and a transducer arm from one sliding base.

See it on Amazon

Pros

  • Screen and transducer on one setup
  • Extending transducer arm
  • Slides along an existing track

Cons

  • Best with a gear track installed
  • Drill-down track option needs a rigid surface

The WINDFRD Fish Finder Track Mount with Transducer suits an inflatable with a gear track and a need for both screen and transducer control. It is a 2-in-1 setup on a single track base.

The display side uses a 1.5-inch double-socket ball for clamping force. The transducer arm extends from 11.42 to 17.91 inches, so you can reach the right depth from a seated position without leaning over the side.

A universal track ball and T-bolt let the whole unit slide along the track for quick repositioning. A drill-down mounting track is also in the box for a fixed install, plus four sets of M5 x 20 marine-grade 316L stainless screws and lock nuts.

WINDFRD lists Garmin Striker and ECHOMAP, Lowrance Elite and Hook models, and Humminbird Piranha MAX 4DI. The main structure is glass-reinforced nylon with aluminum hardware, which keeps weight down at 0.85 kg while resisting corrosion.

The trade-off is that the best use needs a track. On a plain inflatable with no track, a clamp or a floor-board bolt base is simpler, and the 10 pound capacity is lower than the swing arm above.

WINDFRD Fish Finder Track Mount with TransducerCheck it on Amazon
6

Leenconghui for Garmin Striker 4 / Plus: Best for small Garmin Striker screens

Leenconghui for Garmin Striker 4 / Plus, fish finder mounts for inflatable boats
8.7/10Our score
  • 5.91-inch aluminum arm
  • 1-inch ball and round base
  • T-bolt track ball
  • AMPS hole pattern

A small aluminum ball mount aimed at Garmin Striker 4 and similar compact screens.

See it on Amazon

Pros

  • Light aluminum arm
  • T-bolt for track use without drilling
  • Compact fit for small Garmins

Cons

  • Narrow model list centered on Striker 4
  • 1-inch ball is lighter duty than 1.5-inch options

The Leenconghui mount for Garmin Striker 4 suits a small inflatable with a Striker 4, Striker Plus 4cv or Striker Vivid 4cv. It is built around a 5.91-inch aluminum arm and a 1-inch ball.

The kit has AMPS 1-inch ball and round bases, plus a T-bolt track ball. That mix lets you use a round base on a flat spot or a T-bolt on a track, with no drilling for the track option, which suits a boat you do not want to modify.

The AMPS hole pattern also fits GPS units and other devices. Leenconghui lists Striker 4 models, echo models, ECHOMAP Plus 42cv to 45cv, and ECHOMAP UHD2 6, so check your exact Garmin suffix before you order.

The aluminum base and fused rubber ball help the mount stay put on bumpy water. The compact size suits a small boat where a large arm would crowd your gear, and the round base spreads load on a small rigid patch.

The trade-off is scope. This is a small-screen, Garmin-focused kit with a 1-inch ball.

A larger 9 or 12 inch display needs a heavier 1.5-inch arm from this list, especially in chop on a flexing hull.

Leenconghui for Garmin Striker 4 / PlusCheck it on Amazon
7

xik 1.5 Ball Medium Arm Fish Finder: Best for Garmin and Lowrance 1.5-inch systems

xik 1.5 Ball Medium Arm Fish Finder, fish finder mounts for inflatable boats
8.5/10Our score
  • 1.5-inch ball system
  • 5.91-inch dual socket arm
  • 2.4-inch round base
  • Rectangular plate with mounting screw kit

A medium aluminum alloy arm on a 1.5-inch ball, with a round base for flat surfaces.

See it on Amazon

Pros

  • 1.5-inch ball for stronger clamp
  • Pre-drilled rectangular plate
  • Wide Garmin and Lowrance list

Cons

  • Not for listed Humminbird Helix and Solix models
  • Round base needs a flat surface

The xik 1.5 Ball Medium Arm Fish Finder Mount suits an inflatable with a flat floor board or transom plate. It uses a 1.5-inch ball system with a 5.91-inch dual socket arm.

The 2.4-inch round base installs on a flat surface. The rectangular plate has pre-drilled holes and a mounting screw kit for common marine electronics, including GPS devices, radios and gimbal mounts, so one base can do more than one job.

xik lists a long Garmin range, including GPSMAP, Striker, ECHOMAP Plus, ECHOMAP UHD and ECHOMAP Ultra models. It also lists Lowrance Eagle, Elite FS, HDS and Hook Reveal models, which covers many mid size screens.

The 1.5-inch rubber ball allows 360-degree rotation and a firmer grip than a 1-inch ball. It supports up to 16 pounds stationary and 6 pounds in motion, and the build is aluminum alloy with TPU for harsh marine use.

The trade-off is a clear exclusion list. xik says it is not compatible with Humminbird Helix 5, 7, 9, 10, 12, Helix 15, Ion, Onix, Solix 10 or PiranhaMax models. Check your exact Humminbird model before you buy, and plan on screws into a rigid surface.

xik 1.5 Ball Medium Arm Fish FinderCheck it on Amazon
8

Millennium Marine Double Face Marine Electronic Mount: Best for two monitors on a pedestal

Millennium Marine Double Face Marine Electronic Mount, fish finder mounts for inflatable boats
8.3/10Our score
  • Telescoping riser adjusts 18 to 24 inches
  • Base swivels 180 degrees
  • Face plate swivels 350 degrees
  • Anodized aluminum

A tall double-face pedestal mount that can hold two 12-inch monitors.

See it on Amazon

Pros

  • Adjusts from 18 to 24 inches tall
  • Can hold two 12-inch monitors
  • Wide swivel range at base and plate

Cons

  • Tall pedestal is heavy for a small inflatable
  • Needs a secure flat base point

The Millennium Marine Double Face Marine Electronic Mount suits a larger inflatable with a solid center area, such as a bigger boat with a rigid deck insert. It is a pedestal, not a compact arm.

The telescoping riser adjusts from 18 to 24 inches in height. That tall reach can lift a screen above seated anglers or a cooler, and it helps when a low tube boat puts your sight line too close to the water.

The base swivels 180 degrees and the face plate swivels 350 degrees. You can aim two screens toward different seats without remounting, and the riser also tilts, so trimming the angle is faster than moving the whole base.

Millennium Marine says the face plate can fit most brands and can hold two 12-inch monitors. The build is anodized aluminum with heavy-duty stainless steel hardware, and the kit includes the base station, telescopic riser, face plate and hardware.

The trade-off is size and weight for a small inflatable. A tall pedestal adds leverage when the boat flexes and bounces.

On a small tube boat, a low ball or swing arm is easier to keep steady and less likely to block space.

For comparison on a bigger hull, see our best fish finder mount for pontoon boat guide.

Millennium Marine Double Face Marine Electronic MountCheck it on Amazon
9

BLKGJTF 0368 Fish Finder Mount: Best for a compact budget bracket

BLKGJTF 0368 Fish Finder Mount, fish finder mounts for inflatable boats
7.9/10Our score
  • For 7 to 9 inch screens
  • Ball and socket design
  • Engineering-grade nylon and stainless steel fasteners
  • Adjustable

A compact nylon ball bracket for 7 to 9 inch screens, with plug-and-play install.

See it on Amazon

Pros

  • Compact and light
  • Stepless adjustment
  • Simple plug-and-play style install

Cons

  • Nylon build is less rigid than aluminum
  • No track or clamp base in the box

The BLKGJTF 0368 Fish Finder Mount suits a small inflatable and a 7 to 9 inch screen on a budget. It is a compact nylon ball bracket with adjustable positioning.

The ball and socket design gives angle choices. You can tilt the screen up for standing use or down for seated use, and the flat face is sized for 7 to 9 inch screens rather than the 12 inch units above.

BLKGJTF builds it from engineering-grade nylon with stainless steel fasteners. The mount is light, at 0.19 kg, so it adds little load to a soft-sided boat that already flexes, and it is listed as waterproof.

Install is described as plug and play with stepless rotation. That speed helps if you remove the screen for storage after each trip, since inflatables are often deflated or folded between outings.

The trade-off is rigidity and base choice. Nylon flexes more than the aluminum arms above, and no track or clamp base is in the box.

You still need a flat spot or a separate base to fix it to, and the 196 g capacity in the specs is for the bracket itself.

BLKGJTF 0368 Fish Finder MountCheck it on Amazon

How do these mounts compare for inflatable tubes?

The comparison below shows base type first, because base type decides tube safety. Check the base column before you look at arm length.

ProductBest forArm lengthMaterialScreen fitOur score
WINDFRD Aluminum Swing Arm Fish Finder Mountlarge screens on a rigid mount point6 inchesAluminum and stainless steel hardware5 to 12 inches9.6
Vadaxx Fish Finder Mount Basea simple ball-mount base6 inchesNylon and stainless steel9.2
EDSRDPLT Universal Kayak Fish Finder Mounttool-free track mounting9 to 14 inchesMarine-grade composite and stainless steel9.2
Deeper Kayak Flexible Arm Fish Finder Mountclamping without drilling31 inchesStainless steel, aluminum, fiber-glass reinforced plastic9.1
WINDFRD Fish Finder Track Mount with Transducerscreen plus transducer on one track17.91 inchesGlass-reinforced nylon, aluminum hardware8.8
Leenconghui for Garmin Striker 4 / Plussmall Garmin Striker screens5.91 inchesAluminum8.7
xik 1.5 Ball Medium Arm Fish FinderGarmin and Lowrance 1.5-inch systems5.91 inchesAluminum alloy and TPU8.5
Millennium Marine Double Face Marine Electronic Mounttwo monitors on a pedestal24 inchesAnodized aluminum8.3
BLKGJTF 0368 Fish Finder Mounta compact budget bracketNylon and stainless steel fasteners7 to 9 inches7.9

For inflatable use, a track or clamp base beats a screw base on a soft surface. A screw base is fine only on a rigid board or transom.

The table makes that split clear.

A 1.5-inch ball gives more clamp force than a 1-inch ball. That matters with 9 to 12 inch screens on a flexing hull.

A 1-inch ball is still fine for a small Striker 4.

Arm length helps reach, but a long arm also magnifies wobble. The 6-inch arms here are a safe middle ground for small boats.

The 31-inch Deeper arm is long because it holds a floating sonar, not a screen.

What the table does not show

The table cannot show flex. Two mounts with the same arm length can feel very different on tubes.

Aluminum arms tend to hold a set angle longer than nylon arms under repeated bounce.

How to read capacity numbers

Static and dynamic ratings are not the same. A mount rated for a high static load may have a much lower rating in motion.

Use the dynamic figure when you judge chop and wave impact.

How we compared these mounts

We compared specs, features and buyer feedback against inflatable-boat needs. We looked at base type, materials, screen fit and arm range for each pick.

We checked which models are track, clamp, swing arm, ball mount or pedestal. That split drives the ranking more than price tier.

We also checked each maker's stated compatibility. We kept brand claims labeled by brand, and we did not add specs that were not in the data.

Our fish finders explainer covers what the display shows once it is mounted. Mount choice and sonar performance are linked, but they are separate buys.

Which base is safest for inflatable tubes?

A clamp or track base is safest for most inflatables. Both avoid screws through tubes and keep loads on a rigid edge or rail.

Clamp bases

A G-Clamp grips a transom board or floor edge up to its thickness limit. The Deeper arm clamps to 2.7 inches or less.

Measure your edge first.

Track bases

A T-bolt or track ball slides into a gear track on a rigid rail. The EDSRDPLT and WINDFRD track kits use this method.

No drilling is needed for the track itself.

Screw bases

A screw base needs a flat rigid surface. The WINDFRD swing arm, Vadaxx base and xik arm all use this type.

Never screw into an inflatable tube or an air chamber seam.

Our main best fish finder mount for boat guide ranks mounts for rigid hulls. Inflatable rules are stricter, so use the base checks here first.

What screen size should you mount on an inflatable?

A 5 to 7 inch screen is easiest to keep steady on a small inflatable. A 9 to 12 inch screen needs a heavier arm and a rigid base.

Small screens, 5 to 7 inches

Small Garmins like Striker 4 fit the Leenconghui 1-inch ball kit. A 6-inch arm keeps the screen close to the base, which limits wobble.

Mid screens, 7 to 9 inches

The Vadaxx flat panel and the BLKGJTF 7 to 9 inch bracket sit in this range. Use a 1.5-inch ball if the boat sees chop.

Large screens, 9 to 12 inches

The WINDFRD swing arm is built for 5 to 12 inch screens. The Millennium pedestal can hold two 12-inch monitors, but only on a larger inflatable with a solid center.

Do you need a track mount or a swing arm?

A track mount suits boats that already have a gear track. A swing arm suits boats with a flat rigid surface but no track.

Track mounts

Track mounts slide for repositioning and remove fast for storage. The WINDFRD track mount also carries a transducer arm.

That helps if you want one base for two jobs.

Swing arms

Swing arms pivot at two points and hold larger screens. The WINDFRD aluminum arm is the lead pick here.

It needs screws into a rigid surface, so plan the spot before you drill.

Ball mounts

Ball mounts give the widest angle range on a small base. The Vadaxx and xik picks use ball joints at different sizes.

Pick ball size by screen weight and chop.

If your boat is a small aluminum hull instead, our best fish finder mount for aluminum boat guide covers screw-in bases that are safe on metal.

How do you keep a mount steady on a flexing hull?

Tighten the joints, keep the arm short, and mount low. Those three steps cut most wobble on an inflatable.

Keep the arm short

A 6-inch arm wobbles less than a 14-inch arm with the same screen. Use the longer arms only when reach is a real need.

Mount low and close

A low base near your seat helps you read the screen without leaning. It also keeps the center of gravity down in a tippy boat.

Lock the joints after aiming

Set the angle at the dock, then tighten the knobs or socket arms. Check them again after the first run, because vibration can loosen plastic and nylon joints.

For a small flat-bottom hull, compare with our best fish finder mount for jon boat guide. Jon boats are rigid, so mounts can be bolder there than on tubes.

What should you check before you order?

Check base type, screen fit, and clamp or track size before you order. Those three checks prevent most returns.

Measure your mount point

Measure the thickness of a transom board for a clamp. Measure the track width for a T-bolt.

Write both numbers down before you shop.

Match the exact screen model

Use the maker's compatibility list for your exact model, not just the brand. The xik mount, for example, excludes several Humminbird Helix and Solix models.

Plan storage and removal

Inflatables are stored deflated or folded, so a fast-release base helps. Track and ball mounts come off in seconds.

Bolted swing arms stay on the board.

Verdict: which mount should you buy for an inflatable boat?

Pick the WINDFRD Aluminum Swing Arm if you have a rigid floor board or transom plate and a 5 to 12 inch screen. Pick the Deeper flexible arm if you fish with a Deeper sonar and want no drilling.

Pick a track kit like EDSRDPLT or WINDFRD if your inflatable already has a gear track.

For a small Garmin Striker 4, the Leenconghui kit is the focused fit. For two large monitors in a big inflatable, the Millennium pedestal is the only tall option here, but it needs a solid center base.

When in doubt, protect the tubes first and buy the base that matches your boat. A steady mount on a rigid point will beat a fancy arm fixed to a soft tube every trip.

Our top 3 picks at a glance

  1. 1 WINDFRD Aluminum Swing Arm Fish Finder Mount
    Best for large screens on a rigid mount point

    WINDFRD Aluminum Swing Arm Fish Finder Mount

    9.6/10 our score

    See it on Amazon
  2. 2 Vadaxx Fish Finder Mount Base
    Best for a simple ball-mount base

    Vadaxx Fish Finder Mount Base

    9.2/10 our score

    See it on Amazon
  3. 3 EDSRDPLT Universal Kayak Fish Finder Mount
    Best for tool-free track mounting

    EDSRDPLT Universal Kayak Fish Finder Mount

    9.2/10 our score

    See it on Amazon

Frequently asked questions

Can you drill a fish finder mount into an inflatable boat tube?

Avoid drilling inflatable tubes. A screw hole can leak and weaken the tube.

Use a clamp, a track on a rigid floor board or transom, or a flat surface away from air chambers instead.

What is the safest mount point on a small inflatable boat?

A rigid floor board, a transom plate or a gear track fixed to a hard surface is safest. Those points keep screw loads out of soft tubes and stop the display from shifting when the boat flexes.

Do I need a transducer arm as well as a screen mount?

Many inflatables use a transom or over-side transducer setup, so a screen mount alone may be enough. Track kits that add a transducer arm help if you want both parts positioned from one base.

Which mount suits a Deeper sonar on an inflatable boat?

A clamp arm made for Deeper models suits this use, because it holds the sonar at the surface and clamps to a rigid edge. Check the clamp thickness limit against your transom or floor board before you order.