Best picks

9 Best Mounts for the Lowrance Eagle 7 (November 2026)

Updated on · By the Fish Finder Critic team

The best Lowrance Eagle 7 mounts include the Scotty 0163 Ball-Mount Fish Finder and Universal for most boats, the WINDFRD Cast Aluminum C Size 1.5" Short for short reach, and the WINDFRD Aluminum Swing Arm Fish Finder Mount for dashboard swing.

On this page (9 sections)
  1. Screen mounts and sensor mounts in this best Lowrance Eagle 7 mount roundup
  2. How do these Lowrance Eagle 7 mounts compare on arm length and hold?
  3. How we compared these mounts for secure and adjustable placement
  4. What size plate do you need for the Lowrance Eagle 7?
  5. How long should the arm be on a best Lowrance Eagle 7 mount?
  6. Ball mount, swing arm or gimbal: which is best for the Eagle 7?
  7. How tight should you set the mount before you run?
  8. Can you mount the Eagle Eye 9 sensor with the same mount as the Eagle 7 screen?
  9. Verdict: which best Lowrance Eagle 7 mount should you buy?

The best Lowrance Eagle 7 mount for most boats is the Scotty 0163 Ball-Mount Fish Finder and Universal Mounting Plate. Its plate is made for 7 to 9 inch fish finders, so your 7 inch Eagle 7 screen is the size it was sized for.

You should still choose by placement, not by brand alone. A short mount puts the screen close to the helm.

A long mount reaches over a deep console. A gimbal holds one spot and tilts.

A pole clamp holds a transducer, not a screen.

If you are still deciding between Lowrance units, our best Lowrance fish finder roundup helps you place the Eagle 7 in the wider line. If you want a smaller Lowrance unit for comparison, see the Lowrance HOOK Reveal 5 fish finder review.

For the full install steps, read how to install a Lowrance Eagle 7. For transducer sizing, check Lowrance Eagle Eye 9 dimensions.

For first use tips, see the Lowrance Eagle 7 setup guide.

Our picks at a glance

  1. 1 Scotty 0163 Ball-Mount Fish Finder and Universal
  2. 2 WINDFRD Cast Aluminum C Size 1.5" Short
    Best for short reach

    WINDFRD Cast Aluminum C Size 1.5" Short

    9.7/10 our score

    See it on Amazon
  3. 3 WINDFRD Aluminum Swing Arm Fish Finder Mount
    Best for dashboard swing

    WINDFRD Aluminum Swing Arm Fish Finder Mount

    9.6/10 our score

    See it on Amazon
  1. 4WINDFRD 1.5" Ball Medium Arm Fish FinderCheck it
  2. 5Vadaxx Fish Finder Mount Base

    Vadaxx Fish Finder Mount Base

    Best for simple flat surface
    Check it
  3. 6Koroao Adjustable Pole Clamp Transducer Mount CompatibleCheck it
  4. 7JISHAHS Aluminum Mount for Lowrance Eagle Eye

    JISHAHS Aluminum Mount for Lowrance Eagle Eye

    Best for Eagle Eye 9 rod mount
    Check it
  5. 8VAZESWIN 1.5 Ball Aluminum Alloy Fish FinderCheck it
  6. 9TUSITA Tilt/Swivel Gimbal Mount Bracket and KnobsCheck it

Screen mounts and sensor mounts in this best Lowrance Eagle 7 mount roundup

Seven picks hold the Eagle 7 screen. Two picks hold the Eagle Eye 9 sensor on a pole or rod.

That split matters, because a sensor clamp will not hold your screen and a screen arm will not hold your transducer.

Our score weighs specs, features and buyer feedback against what you are shopping for. A mount that names the Eagle 7 scores higher for fit.

A mount that only fits by screen size scores well when that size range is clear. A sensor-only mount scores lower here because it solves a different job.

1

Scotty 0163 Ball-Mount Fish Finder and Universal: Best for most boats

Scotty 0163 Ball-Mount Fish Finder and Universal, Lowrance Eagle 7 mounts
9.7/10Our score
  • 1.5 inch ball mount
  • Plate sized for 7 to 9 inch fish finders
  • 6.5 inch tall mount
  • 2.25 x 2.25 inch base

A short ball mount sized for 7 to 9 inch screens, so the Eagle 7 sits close and steady.

See it on Amazon

Pros

  • Plate sized for 7 to 9 inch screens
  • Short 6.5 inch height limits wobble
  • Smooth full range of ball motion

Cons

  • Limited reach on wide consoles
  • Plastic enclosure material

The Scotty 0163 suits a boat where the mount point is close to the helm. Its plate is designed for 7 to 9 inch fish finders, so the Eagle 7 is in the middle of that range.

You do not need to guess about plate size.

The mount stands 6.5 inches tall on a 2.25 x 2.25 inch base. That short height is the key benefit.

A short post moves less than a long arm when waves hit. The screen stays where you set it.

The 1.5 inch ball gives a smooth full range of motion. Scotty says the bigger ball design gives greater clamping force for larger accessories.

In daily use, that means you can tilt the screen down for sun glare or up for a standing helm position.

The trade-off is reach. If your console is wide and the flat surface is set back, this mount may leave the screen too far from the wheel.

In that case, one of the longer WINDFRD arms below will fit better. For a close helm, this is the cleanest hold in the group.

Scotty 0163 Ball-Mount Fish Finder and UniversalCheck it on Amazon
2

WINDFRD Cast Aluminum C Size 1.5" Short: Best for short reach

WINDFRD Cast Aluminum C Size 1.5" Short, Lowrance Eagle 7 mounts
9.7/10Our score
  • C size 1.5 inch ball
  • 3.35 inch double socket arm
  • 6.23 x 2 inch universal plate
  • 15.5 lb capacity at rest

A cast aluminum short arm that lists the Eagle 7 as compatible and holds at 15.5 lb at rest.

See it on Amazon

Pros

  • Lists Eagle 7 as compatible
  • Cast aluminum construction
  • Includes 316L stainless mounting kit

Cons

  • Short arm limits placement options
  • Lower dynamic load than static load

This WINDFRD short arm suits a helm where the base sits near the wheel. It lists the Eagle 7 as compatible by name, along with the Eagle 9 and Elite FS 7.

That named fit removes doubt about hole patterns.

The arm is 3.35 inches long with a C size 1.5 inch ball. The plate is 6.23 x 2 inches with pre-drilled holes for marine electronics.

The round base is 2.4 inches in diameter for a flat surface install.

WINDFRD says the mount holds up to 15.5 lb at rest and 6.6 lb while moving. That gap matters.

A screen that feels solid at the dock can still shift at speed or in chop. Tighten the socket arm and check it after the first run.

The build is cast aluminum in one piece with stainless steel hardware. It includes a complimentary 316L marine grade stainless steel mounting kit.

The trade-off is reach. At 3.35 inches, this is the shortest arm here, so it suits close placement only.

WINDFRD Cast Aluminum C Size 1.5" ShortCheck it on Amazon
3

WINDFRD Aluminum Swing Arm Fish Finder Mount: Best for dashboard swing

WINDFRD Aluminum Swing Arm Fish Finder Mount, Lowrance Eagle 7 mounts
9.6/10Our score
  • For 5 to 12 inch screens
  • Two pivot points for 360 degree rotation
  • 6 inch arm
  • 110 lb static capacity

A swing arm with two pivots for moving the Eagle 7 side to side or turning it toward you.

See it on Amazon

Pros

  • Two pivots for wide swing
  • Lists Eagle 7 as compatible
  • High static load capacity

Cons

  • Larger footprint than ball mounts
  • Swing can shift under wave impact

This WINDFRD swing arm suits a dashboard where you need to move the screen side to side. It is made for 5 to 12 inch screens, so the Eagle 7 is well inside that range.

It also lists the Eagle 7 as compatible by name.

The arm is 6 inches long with two pivot points for 360 degree rotation. One pivot at the base and one at the plate let you swing the screen toward a passenger seat or turn it toward you.

That swing is the main reason to pick this over a ball mount.

WINDFRD says it holds up to 110 lb static and 22 lb dynamic. The static number is far higher than any 7 inch screen needs.

The dynamic number is the one to watch. A swing arm can drift under wave impact if the pivots are loose.

The base installs on dashboards, decks of boats and kayaks, on any flat surface. It includes 4 sets of 316 marine grade stainless steel screws and lock nuts.

The trade-off is footprint. This arm takes more dash space than a 2.4 inch round ball base.

WINDFRD Aluminum Swing Arm Fish Finder MountCheck it on Amazon
4

WINDFRD 1.5" Ball Medium Arm Fish Finder: Best for medium reach

WINDFRD 1.5" Ball Medium Arm Fish Finder, Lowrance Eagle 7 mounts
9.5/10Our score
  • C size 1.5 inch ball
  • 5.9 inch double socket arm
  • 6.23 x 2 inch mounting plate
  • 15.5 lb static load

A medium 5.9 inch arm that adds reach over the short version while keeping a 1.5 inch ball joint.

See it on Amazon

Pros

  • Lists Eagle 7 as compatible
  • More reach than short arm
  • Includes 316L stainless mounting kit

Cons

  • More flex than short arm
  • Moving load limit is lower

This WINDFRD medium arm suits a console where the short arm will not reach. It lists the Eagle 7 as compatible by name, and it uses the same C size 1.5 inch ball system as the short version.

The plate is 6.23 x 2 inches.

The arm is 5.9 inches long, almost twice the reach of the 3.35 inch short arm. That extra reach lets you clear a console edge or a storage hatch.

The round base is 2.4 inches in diameter with an AMPS hole pattern.

WINDFRD says the mount supports up to 15.5 lb static and 4.5 lb while moving. The moving limit is lower than the short arm's moving limit.

That is a fair trade for more reach. A longer arm flexes more, so set the screen lower and closer when you are running in rough water.

It is made of marine grade aluminum with stainless steel hardware and a powder coat finish. It includes a 316L stainless steel mounting kit.

Choose this over the short version when placement needs reach. Choose the short version when stability matters more than reach.

WINDFRD 1.5" Ball Medium Arm Fish FinderCheck it on Amazon
5

Vadaxx Fish Finder Mount Base: Best for simple flat surface

Vadaxx Fish Finder Mount Base, Lowrance Eagle 7 mounts
9.2/10Our score
  • Dual 360 degree swivel ball mount
  • 1.8 inch swivel ball
  • 2.6 inch base diameter
  • 5.9 inch total height

A nylon and stainless ball base with a 1.8 inch ball for a simple flat surface install.

See it on Amazon

Pros

  • Dual 360 degree swivel
  • 1.8 inch ball for strong hold
  • Includes 4 screws and 4 nuts

Cons

  • No Eagle 7 named in compatibility
  • Not water resistant

The Vadaxx base suits a simple flat surface install where you want a ball swivel without a long arm. It has dual 360 degree swivel ball mount joints at the base and the bracket.

The swivel ball is 1.8 inches in diameter on a 2.6 inch base.

The total height is about 5.9 inches, with a top flat panel about 6.3 x 2.1 inches. That panel is wide enough for a 7 inch screen class device.

The flat surface has various mounting holes, and you can drill your own holes to fit your model.

Vadaxx says the mount is made of nylon and stainless steel. It includes 4 screws and 4 nuts.

The side switch loosens both ball joints so you can set your angle, then you tighten it to hold.

The trade-off is fit certainty. This mount does not name the Eagle 7 in its compatibility list.

It relies on a universal flat plate. It is also not water resistant, so rinse and dry it after saltwater use.

If you want a named Eagle 7 fit, the WINDFRD or TUSITA picks above are safer bets.

Vadaxx Fish Finder Mount BaseCheck it on Amazon
6

Koroao Adjustable Pole Clamp Transducer Mount Compatible: Best for Eagle Eye 9 pole clamp

Koroao Adjustable Pole Clamp Transducer Mount Compatible, Lowrance Eagle 7 mounts
9.1/10Our score
  • Fits round poles 20 to 50 mm
  • Dual bolt securing system
  • M6x40mm bolt
  • Nylon, stainless steel and silicone

A pole clamp for the Eagle Eye 9 transducer on round poles from 20 to 50 mm, not a screen mount.

See it on Amazon

Pros

  • Fits 20 to 50 mm poles
  • Dual bolt securing system
  • Quick release design

Cons

  • Transducer mount, not screen mount
  • Clamp only, sensor not included

The Koroao clamp suits an Eagle Eye 9 transducer on a round pole, not an Eagle 7 screen. It fits round poles from 20 to 50 mm in diameter.

That range covers many trolling motor shafts and stand pipes.

It uses a dual bolt securing system with an M6x40mm bolt. The bolt lock design is meant to keep the sensor fixed under vibration.

Koroao says no additional tools or accessories are needed for install.

The clamp is made of nylon, stainless steel and silicone. That mix resists corrosion in a harsh marine setting.

The quick release feature lets you remove the clamp for storage or for moving it to another pole.

The trade-off is job fit. This is a clamp mount only, and the Eagle Eye 9 is not included.

It will not hold your Eagle 7 display. Buy it only if you are mounting the Eagle Eye 9 sensor and you have a pole in the 20 to 50 mm range.

For screen placement, stay with the ball mounts and gimbal above.

Koroao Adjustable Pole Clamp Transducer Mount CompatibleCheck it on Amazon
7

JISHAHS Aluminum Mount for Lowrance Eagle Eye: Best for Eagle Eye 9 rod mount

JISHAHS Aluminum Mount for Lowrance Eagle Eye, Lowrance Eagle 7 mounts
8.9/10Our score
  • Fits rods 1 to 1.5 inch diameter
  • Aluminum alloy construction
  • M6x40mm bolt
  • One piece bolt lock design

An aluminum rod mount for the Eagle Eye 9 sensor on rods from 1 to 1.5 inches in diameter.

See it on Amazon

Pros

  • Fits 1 to 1.5 inch rods
  • Aluminum alloy construction
  • Vibration resistant bolt lock

Cons

  • Sensor mount, not screen mount
  • Narrow rod diameter range

The JISHAHS mount suits an Eagle Eye 9 sensor on a rod, not an Eagle 7 screen. It fits rod diameters from 1 to 1.5 inches.

That includes 3/4 inch PVC via adapters noted by the brand, plus Summit rods and carbon fiber rods in that diameter range.

It is made of aluminum alloy with an anodized black finish. The one piece bolt lock design uses an M6x40mm bolt.

JISHAHS says the bolt system keeps the sensor attached without loosening from vibration.

Aluminum alloy is the main benefit here. It costs more than a nylon clamp but it resists bending and holds torque better on a rod that flexes.

The mount weighs 0.18 kg, so it adds little weight to a rod set up.

The trade-off is narrow fit and job fit. The rod range is 1 to 1.5 inches only, so measure your rod before you order.

This mount also will not hold your Eagle 7 screen. Pick it for an Eagle Eye 9 rod install.

Pick a ball arm or gimbal for the Eagle 7 display itself.

JISHAHS Aluminum Mount for Lowrance Eagle EyeCheck it on Amazon
8

VAZESWIN 1.5 Ball Aluminum Alloy Fish Finder: Best for long reach

VAZESWIN 1.5 Ball Aluminum Alloy Fish Finder, Lowrance Eagle 7 mounts
8.6/10Our score
  • 9.1 inch long double socket arm
  • 2.4 inch round base
  • 6.25 x 2 inch rectangular plate
  • 6061-T6 aluminum alloy

A long 9.1 inch arm for placing the Eagle 7 well away from the base when the console is deep.

See it on Amazon

Pros

  • Lists Eagle 7 as compatible
  • Long 9.1 inch arm
  • 360 degree rotation

Cons

  • Long arm can flex more
  • No installation screws included

The VAZESWIN long arm suits a deep console where the screen needs to sit well away from the base. The arm is 9.1 inches long, the longest in this roundup.

It lists the Eagle 7 as compatible by name.

The package has a 2.4 inch round base, a 9.1 inch double socket arm and a 6.25 x 2 inch rectangular plate. The base and plate are thickened 6061-T6 aluminum alloy with hard anodized surfaces.

The arm is powder coated 6061-T6 aluminum.

The long arm gives you placement that a short arm cannot. You can mount the base on a flat deck and reach the screen over a hatch or a console lip.

The ball and socket design gives 360 degree rotation for tilt and turn.

The trade-off is flex. A 9.1 inch arm will move more than a 3.35 inch arm under waves.

Set the screen as low as you can and tighten the arm fully. Note that the package does not include installation screws and other hardware, so plan for screws before install day.

VAZESWIN 1.5 Ball Aluminum Alloy Fish FinderCheck it on Amazon
9

TUSITA Tilt/Swivel Gimbal Mount Bracket and Knobs: Best for Lowrance gimbal fit

TUSITA Tilt/Swivel Gimbal Mount Bracket and Knobs, Lowrance Eagle 7 mounts
8.5/10Our score
  • Compatible with Eagle 7 fishfinder
  • Tilt and swivel adjustment
  • Model 000-11019-001
  • Includes bracket, 2 knobs and hardware

A Lowrance-specific gimbal bracket for the Eagle 7 with tilt and swivel and two knobs.

See it on Amazon

Pros

  • Names Eagle 7 as compatible
  • Tilt and swivel adjustment
  • Includes knobs and mounting hardware

Cons

  • Fixed gimbal position, less reach
  • Narrow brand fit

The TUSITA gimbal suits a Lowrance user who wants a bracket made for the Eagle 7. It is compatible with the Lowrance Eagle 7 fishfinder by name, model 000-11019-001.

It also fits HOOK2 and Reveal 7 units in that family.

It gives tilt and swivel adjustment for viewing angle. You set the tilt for sun angle and swivel it toward the helm seat.

Two knobs lock the position. That is simpler than a ball mount, where you set tilt, turn and swing all at once.

The package includes 1 tilt and swivel gimbal mount bracket, 2 knobs and mounting hardware. The enclosure is high strength composite.

The mount is a surface mount for a boat.

The trade-off is reach and range. A gimbal holds the screen at one fixed spot with tilt and swivel only.

It cannot swing the screen across the console the way the WINDFRD swing arm can. If your helm spot is fixed and you want a clean Lowrance fit, this is the right tool.

If your helm spot changes, a ball mount gives you more freedom.

TUSITA Tilt/Swivel Gimbal Mount Bracket and KnobsCheck it on Amazon

How do these Lowrance Eagle 7 mounts compare on arm length and hold?

Arm length is the main difference between the screen mounts. The WINDFRD short arm is 3.35 inches.

The Scotty 0163 stands 6.5 inches tall. The WINDFRD medium arm is 5.9 inches.

The VAZESWIN arm is 9.1 inches.

Short arms hold steadiest. A short arm puts the screen close to the base, so waves move it less.

The WINDFRD short arm lists 15.5 lb at rest and 6.6 lb while moving. The Scotty 0163 is short in height at 6.5 inches, which limits leverage on the base.

Long arms trade some steadiness for placement. The VAZESWIN 9.1 inch arm reaches over a deep console.

The WINDFRD medium arm at 5.9 inches is the middle ground. The swing arm at 6 inches adds side to side swing that a ball arm does not give.

Load numbers need context. The swing arm lists 110 lb static and 22 lb dynamic.

The WINDFRD ball arms list 15.5 lb static. All of those numbers are far above what a 7 inch screen weighs.

The number that matters is the dynamic or moving limit, because that is the load when the boat is moving.

How we compared these mounts for secure and adjustable placement

We compared mounts by fit, arm length, ball size, material and what is included. A mount that names the Eagle 7 scored higher for fit.

A mount that fits by screen size scored higher when that range was clear.

We checked specs for arm length, base size, plate size and load limits. We looked at whether stainless hardware is included.

We noted when screws are not included, as with the VAZESWIN long arm.

We also split screen mounts from sensor mounts. The Koroao and JISHAHS mounts hold the Eagle Eye 9 sensor.

They do not hold the Eagle 7 screen. We kept them in this roundup because many Eagle 7 buyers buy the Eagle Eye 9 and need a pole or rod clamp at the same time.

We did not test these mounts on the water. Our scores weigh specs, features and buyer feedback against what you are shopping for.

That is why a named Eagle 7 fit and a clear screen size range matter so much in the ranking.

What size plate do you need for the Lowrance Eagle 7?

The Eagle 7 is a 7 inch screen, so a plate made for 7 to 9 inch screens fits it. The Scotty 0163 plate is designed for that exact range.

The WINDFRD plates are 6.23 x 2 inches with pre-drilled holes for many marine electronics.

Do pre-drilled holes matter?

Yes, pre-drilled holes save time and reduce drilling errors. The WINDFRD plates have combinations of holes for GPS, radios and gimbal brackets.

The TUSITA gimbal is made for the Eagle 7 by model number, so hole fit is not a guess.

What if the holes do not match?

The Vadaxx base has a flat surface with various mounting holes. You can drill your own holes to fit your model.

That is a good option when a universal plate does not match. Measure twice and drill once, because extra holes in a dash are hard to hide.

How long should the arm be on a best Lowrance Eagle 7 mount?

Short arms suit a base close to the helm. A 3.35 inch arm puts the screen near the wheel and holds it steady.

The Scotty 0163 at 6.5 inches tall suits a similar close placement.

When do you need a medium arm?

A 5.9 inch arm suits a base set back from the wheel. The WINDFRD medium arm reaches over a console edge while keeping a 1.5 inch ball joint.

That is the most common sweet spot for center console boats.

When do you need a long arm?

A 9.1 inch arm suits a deep console, a pontoon setback or a kayak where the base is low. The VAZESWIN long arm reaches that far.

Expect more movement in chop and set the screen lower to reduce swing.

Ball mount, swing arm or gimbal: which is best for the Eagle 7?

A ball mount gives the most adjustment. You can tilt, turn and swing the screen in any direction.

The Scotty 0163, the WINDFRD ball arms and the VAZESWIN arm all use this design. Ball mounts suit a helm position that changes through the day.

When is a swing arm better?

A swing arm suits a dash where the screen needs to move side to side. The WINDFRD swing arm has two pivots for 360 degree rotation.

You can swing the Eagle 7 toward a passenger or turn it toward you without lifting the whole mount.

When is a gimbal better?

A gimbal suits a fixed helm spot. The TUSITA gimbal names the Eagle 7 and gives tilt and swivel with two knobs.

It holds one position cleanly. It does not swing across the console, so it suits a boat where the driver always sits in the same place.

How tight should you set the mount before you run?

Tighten the ball socket or arm until the screen holds still when you push it by hand. Then run at low speed and check it again.

WINDFRD lists lower moving limits than static limits for its ball arms, which is a clear sign that motion changes the load.

What should you check after the first run?

Check the base screws, the socket arm and the plate screws. A base that feels solid at the dock can work loose over the first few runs.

Stainless hardware resists corrosion, but it does not replace a final torque check.

How do you reduce screen bounce in chop?

Lower the screen height as much as placement allows. A lower center of gravity bounces less.

Shorter arms bounce less than longer arms. If you run in rough water often, choose the short WINDFRD arm or the Scotty 0163 over a long arm.

Can you mount the Eagle Eye 9 sensor with the same mount as the Eagle 7 screen?

No, the Eagle Eye 9 sensor needs a pole or rod clamp. The Koroao clamp fits round poles from 20 to 50 mm.

The JISHAHS mount fits rods from 1 to 1.5 inches. Neither holds the Eagle 7 screen.

Which sensor mount fits a pole?

The Koroao clamp fits a round pole from 20 to 50 mm with a dual bolt system and an M6x40mm bolt. Measure your pole in millimeters or convert inches before you order.

A pole just outside that range will clamp poorly.

Which sensor mount fits a rod?

The JISHAHS mount fits rods from 1 to 1.5 inches in diameter. It is aluminum alloy with a one piece bolt lock.

Measure the rod at the spot where the clamp will sit, because rod diameter can taper.

Verdict: which best Lowrance Eagle 7 mount should you buy?

Buy the Scotty 0163 if your mount point is close to the helm, because its plate fits 7 to 9 inch screens and its 6.5 inch height holds the Eagle 7 steady. Buy the WINDFRD short arm if you want a named Eagle 7 fit in cast aluminum with a 3.35 inch arm.

Buy the WINDFRD medium arm if you need 5.9 inches of reach over a console edge.

Buy the WINDFRD swing arm if you need side to side swing from two pivots. Buy the VAZESWIN long arm if your console is deep and you need 9.1 inches of reach.

Buy the TUSITA gimbal if you want a Lowrance-specific bracket with tilt and swivel and two knobs.

Buy the Koroao clamp if you are mounting the Eagle Eye 9 on a 20 to 50 mm pole. Buy the JISHAHS mount if you are mounting the Eagle Eye 9 on a 1 to 1.5 inch rod.

Neither sensor mount will hold your Eagle 7 screen, so pair one with a screen mount above.

Measure your mount point, your pole or your rod before you order. Then pick the shortest arm that reaches your helm spot.

That rule gives you the steadiest hold for the best Lowrance Eagle 7 mount choice on your boat.

Our top 3 picks at a glance

  1. 1 Scotty 0163 Ball-Mount Fish Finder and Universal
  2. 2 WINDFRD Cast Aluminum C Size 1.5" Short
    Best for short reach

    WINDFRD Cast Aluminum C Size 1.5" Short

    9.7/10 our score

    See it on Amazon
  3. 3 WINDFRD Aluminum Swing Arm Fish Finder Mount
    Best for dashboard swing

    WINDFRD Aluminum Swing Arm Fish Finder Mount

    9.6/10 our score

    See it on Amazon

Frequently asked questions

What is the best Lowrance Eagle 7 mount?

For most boats, the Scotty 0163 is the best Lowrance Eagle 7 mount because its plate fits 7 to 9 inch screens and its short 6.5 inch height holds the display steady. Choose a longer WINDFRD or VAZESWIN arm if your console needs more reach, and choose the TUSITA gimbal if you prefer a Lowrance-specific tilt and swivel bracket.

Do these mounts fit the Eagle 7?

Several mounts name the Eagle 7 directly, including WINDFRD models, VAZESWIN and TUSITA. The Scotty 0163 fits by screen size at 7 to 9 inches.

The Vadaxx base uses a universal flat plate.

The Koroao and JISHAHS mounts are for the Eagle Eye 9 sensor, not the Eagle 7 screen.

How long should a mount arm be?

A short 3.35 inch arm suits a hem or dash close to the helm. A medium 5.9 inch arm reaches over a console edge.

A long 9.1 inch arm suits a deep console or a seat set back from the mount point.

Longer arms add placement choice but can move more under waves.

Can I use a gimbal mount instead of a ball mount?

Yes, if your display accepts that bracket. The TUSITA gimbal names the Eagle 7 and gives tilt and swivel adjustment with two knobs.

A gimbal holds a fixed position, while a ball mount lets you swing the screen in many directions.

A ball mount suits changing helm positions better.