Guide

How to Wire a 36V Trolling Motor

Updated on · By the Fish Finder Critic team

To wire a 36V trolling motor, connect three 12V batteries in series, then run fused 6 AWG (or the size your motor requires) positive and negative leads through a disconnect and a 36V-rated plug to the motor. Match the motor's voltage, polarity, and fuse rating exactly, and confirm the wiring with the motor manual before you connect power.

On this page (10 sections)
  1. How do you wire three batteries in series for 36V power?
  2. What parts do you need before you start wiring a 36V motor?
  3. How do you size wire and a breaker for a 36V trolling motor?
  4. How do you connect the plug and receptacle safely?
  5. What is the step-by-step order for wiring a 36V trolling motor?
  6. How do you protect the motor connections from water and heat?
  7. What mistakes should you avoid when wiring a 36V trolling motor?
  8. Which plug setup fits your 36V trolling motor best?
  9. How do you test a 36V trolling motor wiring job?
  10. What should you check before your first trip with a 36V motor?

To wire a 36V trolling motor, connect three 12V batteries in series and run fused, correctly sized leads through a disconnect and a 36V plug to the motor. Wiring 36V trolling motor systems takes more care than 12V or 24V setups because the same current can do more damage when a connection goes wrong.

Start by reading your motor manual for its exact voltage, amperage draw, fuse size, and wire gauge. Write those numbers down, then gather batteries, cable, a breaker, a disconnect switch, terminals, and a plug rated for 36V and your motor's current.

How do you wire three batteries in series for 36V power?

Three 12V batteries in series give you 36V, with amperage staying the same as one battery. A 100 amp-hour battery still gives 100 amp-hours at 36V, not 300.

Connect the positive post of battery one to the negative post of battery two, and the positive post of battery two to the negative post of battery three. The free positive and free negative are your 36V output.

Put a fuse or breaker on that free positive before anything else. Keep the series jumpers short, secure, and covered.

Our guide to how to wire a 24v trolling motor covers the two-battery version.

Do you need all three batteries to match?

Yes, match chemistry, capacity, and condition as closely as you can. Mixed batteries charge and discharge at different rates, which leaves one battery doing more work.

Lithium and lead-acid batteries also need different charge settings. Never charge a series string with a charger set for the wrong chemistry or voltage.

Measure the free ends with a meter before you connect anything. You should read close to 36V.

What parts do you need before you start wiring a 36V motor?

You need three 12V batteries, a fuse or breaker, a disconnect switch, a 36V plug, marine cable, terminals, and a meter. The motor manual adds the exact fuse and wire sizes for your model.

Use tinned copper marine cable, ring terminals, and adhesive heat shrink over each crimp for cleaner, corrosion resistant connections. Mount the disconnect where you can reach it from the helm or bow, and label the positive lead near the battery.

Measure cable for the full run from battery to bow, plus extra for tidy loops. A 36v trolling motor wiring kit helps you compare what a complete kit includes.

How do you size wire and a breaker for a 36V trolling motor?

Size wire and protection from the motor's amperage draw and the total run length, not from voltage alone. Voltage tells you the battery layout, while current tells you how thick the wire must be.

A long run from stern batteries to a bow motor loses more voltage, showing up as heat in thin wire and sluggish performance. When in doubt, go one size larger and check the manual.

Place the breaker or fuse on the positive lead, as close to the battery as practical. Use a breaker rated for DC at or above 36V.

How to wire a 12v trolling motor covers the basics at lower voltage.

What wire gauge works for most 36V trolling motors?

Many 36V motors use 6 AWG, but your manual decides. A motor drawing 50 amps needs heavier wire than one drawing 30 amps, even at the same voltage.

Check the draw on the motor label or in the manual. Then match that number to a wire chart for the full length of the run.

The breaker should protect the wire, so it must trip before the wire overheats.

Never use a larger breaker to stop nuisance trips. Find the cause instead, which is usually an undersized wire, a loose terminal, or a motor drawing more current than it should.

How do you connect the plug and receptacle safely?

Mount the boat receptacle first, wire it to the battery side, then wire the motor plug last.

A 36V plug must handle at least your motor current. A 50 amp plug cannot safely run a 60 amp motor.

Mount it where the plug reaches without pulling tight, with strain relief at both ends. Our roundup of best trolling motor plug and receptacle 12v covers ratings, sealing, and locking.

For 36V, the NOVINO set fits 12V, 24V, 36V, and 48V two wire systems at 50A, with tinned copper contacts and IP67 sealing.

The HKAIMING plug suits 12V systems with 8-gauge wire, so check your motor voltage before using it on a 36V motor. Its wing-tab male plug makes removal easier, and the female receptacle seals against weather.

For higher current, the RVMARINEPAT set handles up to 100 amps with 6 to 4 AWG wire and a fast-locking circular design. Silver-plated brass contacts resist corrosion, and the set includes terminals and screws.

What is the step-by-step order for wiring a 36V trolling motor?

The safe order is batteries, protection, disconnect, receptacle, motor plug, then testing. Leave the motor unplugged until the battery side measures correctly.

Mount the batteries, connect the series jumpers, and measure the free ends for about 36V. Connect the fused positive lead to the disconnect, then to the receptacle, and run the negative lead from the free negative to the receptacle.

Mount the receptacle in the bow where the cord reaches without tension, and keep the disconnect off while you wire the motor plug to match polarity exactly. Reversing polarity can damage the motor or controller.

Plug the motor in, switch on, and test at low speed. If it runs backward, check the manual before swapping leads.

How do you protect the motor connections from water and heat?

Sealed terminals, drip loops, and a fused positive lead protect the motor connections better than any single accessory. Water and heat cause most wiring failures on boats.

Apply adhesive heat shrink over every crimp and coat battery posts with a marine terminal protector after tightening. That seal keeps spray from corroding copper and adding resistance.

Give every cable a drip loop, route cables away from sharp edges and pinch points, and add grommets through panels. Check connections after the first few trips, since loose terminals get warm and corrode faster.

Our guide to what size wire for a trolling motor helps confirm the cable matches the current.

How often should you inspect a 36V trolling motor wiring?

Inspect the wiring after the first trip, then every few trips. Look for warm connectors, green corrosion, cracked insulation, and cables rubbing on edges.

Tug each terminal lightly to check for looseness. Rinse salt spray off with fresh water and dry the area.

Replace any terminal that feels hot during a short test run.

A breaker that trips repeatedly is a warning, not a nuisance. Disconnect power and find the fault before you reset it a third time.

What mistakes should you avoid when wiring a 36V trolling motor?

The common mistakes are reversed polarity, an undersized plug, and protection placed too far from the battery. Each one can damage the motor or start a fire.

Do not connect batteries in parallel when you need 36V, since parallel wiring keeps voltage at 12V. Do not mix battery chemistries in one series string.

Do not reuse a 12V plug on a 36V system unless its rating covers both voltage and current. Do not skip the disconnect, since a breaker alone is not a user switch.

If you are comparing motor types before you wire, our trolling motor buying guide covers voltage, thrust, and features by use case.

Which plug setup fits your 36V trolling motor best?

Choose the plug by current first, then by sealing and ease of use. A 36V motor with a high draw needs a plug rated well above that draw.

The NOVINO set at 50A suits many 36V motors with pre-wired 8 AWG cable and IP67 sealing. The RVMARINEPAT set at 100A gives more headroom for high draw motors and uses heavier 6 to 4 AWG wire.

The HKAIMING plug is a 12V option, so it fits only if your motor runs at 12V.

Our comparison of Minn Kota Endura vs Endura Max helps if you are pairing a plug choice with a motor choice. Likewise, Garmin Force trolling motor reviews cover a higher voltage motor line and its wiring needs.

How do you test a 36V trolling motor wiring job?

Test voltage at the battery, at the receptacle, and at the motor plug before the first real trip. Each reading should stay close to 36V under a light load.

Measure the battery string with the disconnect off, then at the receptacle with the disconnect on and the motor unplugged.

A large drop points to a loose terminal, undersized wire, or a weak battery. Fix the drop at its source rather than accepting slow performance.

Run the motor briefly, listen for humming, check for warm connectors, and confirm forward and reverse.

What should you check before your first trip with a 36V motor?

Confirm voltage, polarity, fuse size, plug rating, and cable routing before you launch. A five-minute check at the dock beats troubleshooting on the water.

Verify the breaker trips at its rated current, the disconnect opens fully, and the receptacle cap closes when unplugged. Confirm the motor cord reaches with slack for steering and tilt.

Stow loose cable, carry a meter and spare fuse or breaker for the first season, and note battery voltages after fishing to spot a weak battery early. Return to how to wire a trolling motor for the full overview.

Frequently asked questions

Can I wire a 36V trolling motor with two batteries?

No. A 36V motor needs 36 volts, which means three 12V batteries in series or one 36V battery.

Two batteries in series give 24V, and connecting them in parallel keeps voltage at 12V, so either setup will not meet a 36V motor's requirement.

What wire size do I need for a 36V trolling motor?

Use the wire size named in your motor manual for its amperage draw and run length. Many 36V setups use 6 AWG because of high current, but a lower-draw motor may allow 8 AWG.

Longer runs need larger wire, and the fuse must match the wire and motor.

How do you wire three batteries in series for 36V?

Connect the positive terminal of one battery to the negative of the next, and repeat for the third. The free positive and free negative become the 36V output.

Keep the same battery type, age, and capacity if possible, and measure voltage from the free ends before connecting the motor.

Do I need a circuit breaker for a 36V trolling motor?

Yes. A 36V trolling motor needs overcurrent protection close to the battery positive, sized for the motor and wire.

A breaker or fuse protects the wiring if it chafes or shorts.

Mount it where you can reset or replace it, and keep it within about 18 inches of the battery when practical.